1
Features / Shutdown & Backup
« on: November 11, 2014, 04:11:14 AM »
Please add shutdown & configuration backup option in GUI
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Configuration / Policy configuration required
« on: November 10, 2014, 06:30:53 AM »
Hi Admin,
All these days I tested the wanos on P2P between 2 networks & output was very good, now I want to put it on MPLS for further testing.
A end got 20 Networks
B end got 15 Networks.
How do I create Policies now.
All these days I tested the wanos on P2P between 2 networks & output was very good, now I want to put it on MPLS for further testing.
A end got 20 Networks
B end got 15 Networks.
How do I create Policies now.
3
Troubleshooting / dupq0 :: ThreadSafeQueue: overflow
« on: November 03, 2014, 01:28:43 PM »
Hi,
What is this error/warning/info
dupq0 :: ThreadSafeQueue: overflow
What is this error/warning/info
dupq0 :: ThreadSafeQueue: overflow
4
Features / Datastore size
« on: October 16, 2014, 12:08:32 PM »
Hi,
What is the data store size, is it possible to show the size details in terms of free space & actual size.
Even system details like processor, RAM, etc.
What is the data store size, is it possible to show the size details in terms of free space & actual size.
Even system details like processor, RAM, etc.
5
Troubleshooting / Regarding wrong policy applied during testing, which caused network to go off..
« on: October 14, 2014, 01:51:50 PM »
Hi,
I was doing some policy settings, one policy was with bypass & same one without bypass, after reset on both ends, machine was not reachable. Even locally over network it was not available, but machine was alive physically at both ends. Strange thing observed after reset.
same rule with bypass & without bypass.
On A:
10.9.64.0/24 10.9.17.0/24 without bypass
10.9.64.0/24 10.9.17.0/24 with bypass
On B:
10.9.17.0/24 10.9.64.0/24 without bypass
10.9.17.0/24 10.9.64.0/24 with bypass
When I logged into machine physically, I was not able to see the ip address on the machine, even Tun0 was not visible, I restarted the machine, but still network was not available, then I had to /etc/wanos/clean.sh then reassign the ip address again. Same was done on other end to bring back network alive.
I was doing some policy settings, one policy was with bypass & same one without bypass, after reset on both ends, machine was not reachable. Even locally over network it was not available, but machine was alive physically at both ends. Strange thing observed after reset.
same rule with bypass & without bypass.
On A:
10.9.64.0/24 10.9.17.0/24 without bypass
10.9.64.0/24 10.9.17.0/24 with bypass
On B:
10.9.17.0/24 10.9.64.0/24 without bypass
10.9.17.0/24 10.9.64.0/24 with bypass
When I logged into machine physically, I was not able to see the ip address on the machine, even Tun0 was not visible, I restarted the machine, but still network was not available, then I had to /etc/wanos/clean.sh then reassign the ip address again. Same was done on other end to bring back network alive.
6
Features / Policies rules modifcation
« on: October 14, 2014, 10:26:13 AM »
Hi,
Provide option to uncheck & check the Policies rules modification without deleting the rules & re-adding it..
even policy refresh should happen without resetting .
Provide option to uncheck & check the Policies rules modification without deleting the rules & re-adding it..
even policy refresh should happen without resetting .
7
Troubleshooting / How to bypass the policies which is already added
« on: October 13, 2014, 06:29:55 AM »
Hi,
I see check box not working after adding policies without bypass, later if I want to select the rule to bypass, its not possible to "tick it". I have to delete the rule & re-add again to bypass & vice versa.
I see check box not working after adding policies without bypass, later if I want to select the rule to bypass, its not possible to "tick it". I have to delete the rule & re-add again to bypass & vice versa.
8
Troubleshooting / Lan0 & wan0 speed
« on: July 16, 2014, 03:09:03 PM »
Hi,
is it necessary to have both Wan0 & LAN0 to be of same speed ?
is it necessary to have both Wan0 & LAN0 to be of same speed ?
9
Installation / loading image to Physical Hdd
« on: July 15, 2014, 10:10:53 AM »
Hi,
I was trying to load image to physical hdd ( 500GB & 1TB ) using DD command, though dd command was successful, wanos is not booting ( no error shown after system restart )
win32 disk image works only for pen drives or portable HDD.
I followed http://wanos.org/wan-optimization/?p=489 tried windows DD & linux also, but still wanos not loading after successful dd
let me know how to load the image to physical hdd.
I was trying to load image to physical hdd ( 500GB & 1TB ) using DD command, though dd command was successful, wanos is not booting ( no error shown after system restart )
win32 disk image works only for pen drives or portable HDD.
I followed http://wanos.org/wan-optimization/?p=489 tried windows DD & linux also, but still wanos not loading after successful dd
let me know how to load the image to physical hdd.
10
General Discussion / Difference between High and Low
« on: July 10, 2014, 02:23:39 PM »Where can I find the difference between core, edge & its limitations in express edition & paid version.
Which is the best optimization scenario when 2 locations are primary ( A connected to B & both are primary, not branch office )
High-High
High-Low
Low-Low
11
Installation / Can I use only core
« on: July 09, 2014, 07:44:12 AM »
Hi,
Can I place the Wan core device to my Internet, whether it will optimize the traffic ?
Can I place the Wan core device to my Internet, whether it will optimize the traffic ?
Pages: [1]