Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - khiloc

Pages: [1] 2
1
Troubleshooting / Re: QOS Settings
« on: May 27, 2015, 04:43:33 PM »
Encrypted protocols can't be optimized?

If they can : what if I want to optimize them?

2
Troubleshooting / Re: QOS Settings
« on: May 27, 2015, 12:41:30 PM »
Ok
so the first 2 default rules, what does they really mean?

1 = does it mean that anything not defined in custom rules is process as QOS high, but bypass the optimization engine?
2- All encrypted traffis, https and stuff are all ignore by optimization engine?
??

3
Troubleshooting / Re: QOS Settings
« on: May 27, 2015, 12:35:13 PM »
OK OK OK
Got it working

just deleted the previous qos rules i just added.
and recreate them but now my custom policies are starting at 3...and i am able to add the UDP shaping policy....

4
Troubleshooting / Re: QOS Settings
« on: May 27, 2015, 12:34:01 PM »
Even this don't work


5
Troubleshooting / Re: QOS Settings
« on: May 27, 2015, 12:20:25 PM »
OK,
But I want class1 also to be shaping….??
and i also need UDP traffic to be optimized....

6
Troubleshooting / Re: QOS Settings
« on: May 27, 2015, 11:54:42 AM »
Ok
Choose shape in drop down but still not able to write in


7
Troubleshooting / QOS Settings
« on: May 27, 2015, 11:33:05 AM »
Hello,

After your help for setting up both end devices, i am on the way setting up QOS.
Here is what i got as available bandwidth:
Branch > HQ : 180 kbps
HQ > branch : 300 kbps

when i try to insert rules it says to limit trafic between 2 cisco call managers to 40 Kbps (for SIP trunk link) and it does not allow me to write anything in shape box.




8
Deployment / Re: deployment behind Firewalls
« on: May 27, 2015, 11:12:05 AM »
By the way, just read : http://wanos.co/wan-optimization/packet-loss-recovery/

But seems to be any settings in dashboard to get this working....
any hint?

9
Deployment / Re: deployment behind Firewalls
« on: May 27, 2015, 10:10:50 AM »
Hello
It is all OK now!
Optimization is working out of the Box!

Now on my implementing QOS

10
Deployment / Re: deployment behind Firewalls
« on: May 20, 2015, 06:17:40 PM »
Thanks for good help.
Got it working.

currently setting up the other side Wanos devices and will send it there later


11
Deployment / Re: deployment behind Firewalls
« on: May 19, 2015, 05:07:42 PM »
yes that's it
it is not detected. Sometimes it is, and some it is not.

Even more, with the integrated card access to the management web interface is working 1 on 2.

12
Deployment / Re: deployment behind Firewalls
« on: May 18, 2015, 02:01:22 PM »
hello.
Just followed all steps and it is ok.

But some weird thins is happening.
i do a cleah.sh , then a wanos-cfg (changed IP) and waas able to connect to the box and acces everything from web interface.
Did a reboot (from web interface) and now no more able to connect to the box.


13
Deployment / Re: deployment behind Firewalls
« on: May 18, 2015, 10:08:28 AM »
Planning to try this to change my tun0 interface IP address:
ifconfig eth0 192.168.80.100 netmask 255.255.255.0 broadcast 192.168.80.255 up
route add default gw 192.168.80.254  (the default gw for this tun0 interface should be the one leading to the intranet, confim?)


And to make this config still there after reboot, is this good:
1- create a file /opt/tun0.sh
#!/bin/sh
ifconfig eth0 192.168.0.21 netmask 255.255.255.0 broadcast 192.168.0.255 up
route add default gw 192.168.0.1

2- Add it to the end of /opt/bootload.sh to start tun0.sh
/opt/eth0.sh &

3- is something missing?


Weird thing. I am using an HP MT 3500 desktop with 500GB and Core i3 processor. Added a Gb NIC in PCI slot.
first boot card was detected and a ifconfig show both card inside.
After a  Ctrl+alt+Del, PCI-E card is not visible.
Did a /etc/wanos/clean.sh
and PCI-e card visible again

14
Deployment / Re: deployment behind Firewalls
« on: May 18, 2015, 09:46:58 AM »
please how to change ip addr pf tun0-00 interface from command line interface?
classical ifconfig?
or specific command?

as i need to change theIP before placing it at it place in the network and accessing it from web browser.

15
Deployment / Re: deployment behind Firewalls
« on: May 18, 2015, 08:55:51 AM »
OK
Thanks for linked forum post.

Being in a french country how to change keyboard layout from cli? tried classical linux commands without success

Pages: [1] 2